914 6 2.0L - VINTAGE RACER
This car was built to race in the HSR WEST 2.0L PORSCHE VINTAGE Challenge. 2.0L single plug, 12.5 CR, 40MM PMO carbs, billet rods, 906 style cams, and
all the little details in-between. 901 side shift trans., 904 mainshaft, billet intermediate case section, all special close ratio gear sets, oil cooling system & 5 point return system, along with a billet torque bias diff.
THIS PICTURE SHOWS THE RIGHT SIDE OF THE ENGINE CARRIER MOUNT - PORSCHE 914 BULK HEAD TO PORSCHE 6 CYLINDER ENGINE CONVERSION - UTILIZES POLYURETHANE BUSHINGS - TIG WELDED STEEL - BLACK POWDER COAT FINISH - 13.50 LBS.
THESE MOUNTS ARE A MUCH IMPROVED DESIGN OVER THE STOCK FACTORY CROSS BAR AND WITH THE DELRIN BUSHINGS OVER THE FACTORY RUBBER WILL LAST MANY TIMES LONGER. THIS ALSO GIVES YOUR ENGINE CONVERSION A CLEANER APPEARANCE. (PART #PMP9146FIWAMO)
* PLEASE SPECIFY BOLT-IN OR WELD IN TYPE WHEN ORDERING
YOU CAN ALSO SEE THE CARE TAKEN WHEN WE ROUTE FUEL AND OIL LINES. THEY ARE ALL RUN IN GOODRIDGE FIRE SLEEVE FOR SAFETY AND TO HELP REDUCE TEMPERATURES IN THE ENGINE AND DRIVERS COMPARTMENT.
The front trunk is the heart of our dry sump oil cooling system. This starts out with a Peterson OIL TANK part# OIL 08-0011-DB - 16 quart (4 gallon) aluminum (race) – dual breather - 9 inch. Diameter X 19 inches tall. Also uses the billet aluminum brackets (part # OIL 08-0101).
The oil is routed to the engine using Goodridge fittings and stainless braided hoses. From the engine it returns through the Peterson remote oil filter remote mount (part # OIL 09-0304), to the front through the Mocal oil thermostat (part # OIL-12THER), that will route the oil through the front Setrab oil cooler (part # PMP 500-15NPT3/4), when needed to keep the engine at optimum temperature.
The installation also includes the Peterson breather/fluid catch tank – spun aluminum type with internal baffling - 2X AN -12 female ports & 1X AN -6AN drain plug – Includes stainless steel strap - 118 MM DIA. - PETERSON FLUID - OIL 08-0400
When a fuel cell is wanted or required there is no finer choice than a Fuel Safe fuel cell. They are used and approved by all sanctioning bodies in every racing application from off road to Indy. If you are looking for a fuel cell, Fuel Safe should be your first and only choice!
FUESA914FC-FUEL CELL - PORSCHE 914 - 14 GALLON - AN-8 FEED - AN-6 RETURN - AN-8 VENT - UTILIZES THE ORIGINAL 914 FILLER NECK, SENDING UNIT AND MOUNTING HARDWARE - RED POWDER COATED FINISH - DESIGNED FOR DIRECT REPLACEMENT OF FACTORY FUEL TANK * ANOTHER PATRICK MOTORSPORTS EXCLUSIVE.
SAF LT10AAA
FIRE SYSTEM - 10 LBS. ALUMINUM FIRE BOTTLE - HALON 1301 - PULL CABLE KIT & 3 NOZZLES WITH ALUMINUM TUBING KIT - DOT APPROVED - MEETS SCCA / NASA REQUIREMENTS - NON SFI CERTIFIED - SAFECRAFT
BUMPER COVER - FRONT - 914-6 GT - INCLUDES OIL COOLER CUTOUT AND MOUNTING BRACKET SET - LIGHTWEIGHT COMPOSITE *REPRODUCTION 914-6 GT PART - SEE OUR PROJECTS GALLERY FOR THIS PART IN USE PART NUMBER BOD 914GTFBWOC
THIS SHOWS THE REMOTE OIL FILTER MOUNT - FREE FLOW RIGHT TO LEFT - AN-12 FITTINGS - GAUGE FEED PORT 1/8 NPT - BILLET ALUMINUM FOR USE WITH 13/16 INCH HP-4 FRAM RACING FILTER - PETERSON (PART # OIL 09-0304)
ALSO NEXT TO THE FILTER YOU CAN SEE THE LEFT SIDE OF OUR ENGINE MOUNT WITH THE DELRIN BUSHINGS, THIS IS A VERY COMPACT AND EFFICIENT DESIGN WE HAVE DESIGNED AND MANUFACTURED.
ENGINE CARRIER MOUNT - PORSCHE 914 BULK HEAD TO PORSCHE 6 CYLINDER ENGINE CONVERSION - UTILIZES POLYURETHANE BUSHINGS - TIG WELDED STEEL - BLACK POWDER COAT FINISH - 13.50 LBS. THESE MOUNTS ARE A MUCH IMPROVED DESIGN OVER THE STOCK FACTORY CROSS BAR AND WITH THE DELRIN BUSHINGS OVER THE FACTORY RUBBER WILL LAST MANY TIMES LONGER. THIS ALSO GIVES YOUR ENGINE CONVERSION A MUCH CLEANER APPEARANCE.
* PLEASE SPECIFY BOLT-IN OR WELD-IN TYPE WHEN ORDERING
The front trunk is the heart of our dry sump oil cooling system. This starts out with a Peterson OIL TANK part# OIL 08-0011-DB - 16 quart (4 gallon) aluminum (race) – dual breather - 9 inch. Diameter X 19 inches tall. Also uses the billet aluminum brackets (part # OIL 08-0101).
The oil is routed to the engine using Goodridge fittings and stainless braided hoses. From the engine it returns through the Peterson remote oil filter remote mount (part # OIL 09-0304), to the front through the Mocal oil thermostat (part # OIL-12THER), that will route the oil through the front Setrab oil cooler (part # PMP 500-15NPT3/4), when needed to keep the engine at optimum temperature.
The installation also includes the Peterson breather/fluid catch tank – spun aluminum type with internal baffling - 2X AN -12 female ports & 1X AN -6AN drain plug – Includes stainless steel strap - 118 MM DIA. - PETERSON FLUID - OIL 08-0400
When a fuel cell is wanted or required there is no finer choice than a Fuel Safe fuel cell. They are used and approved by all sanctioning bodies in every racing application from off road to Indy. If you are looking for a fuel cell, Fuel Safe should be your first and only choice!
FUESA914FC-FUEL CELL - PORSCHE 914 - 14 GALLON - AN-8 FEED - AN-6 RETURN - AN-8 VENT - UTILIZES THE ORIGINAL 914 FILLER NECK, SENDING UNIT AND MOUNTING HARDWARE - RED POWDER COATED FINISH - DESIGNED FOR DIRECT REPLACEMENT OF FACTORY FUEL TANK * ANOTHER PATRICK MOTORSPORTS EXCLUSIVE.
SAF LT10AAA
FIRE SYSTEM - 10 LBS. ALUMINUM FIRE BOTTLE - HALON 1301 - PULL CABLE KIT & 3 NOZZLES WITH ALUMINUM TUBING KIT - DOT APPROVED - MEETS SCCA / NASA REQUIREMENTS - NON SFI CERTIFIED - SAFECRAFT
BUMPER COVER - FRONT - 914-6 GT - INCLUDES OIL COOLER CUTOUT AND MOUNTING BRACKET SET - LIGHTWEIGHT COMPOSITE *REPRODUCTION 914-6 GT PART - SEE OUR PROJECTS GALLERY FOR THIS PART IN USE PART NUMBER BOD 914GTFBWOC
PICTURED FROM THE REAR IS OUR DUAL SPORT EXHAUST SYSTEM - PORSCHE 914 6 - TWIN STAINLESS STEEL MUFFLER SYSTEM WITH POLISHED TIPS - 2.25 INCH (57 MM) O.D. IN / OUT - 914 6 REAR LOWER VALANCE REQUIRES TIP EXIT HOLES PART NUMBER PMP9146DMS
- PATRICK MS EXCLUSIVE -
*SPECIAL HEADER OFFSET REQUIRED FOR FITMENT TO STAINLESS STEEL HEADER SYSTEMS
EXHAUST HEADERS - PORSCHE 914 6 - 1.875 INCH / 44 MM I.D. PRIMARIES - MILD STEEL - THERMAL COATING OPTION: $295.00 PART NUMBER EXHP914.6-178
INTERMEDIATE PLATE - PORSCHE 901 / 911 / 914 TRANSMISSIONS - CNC MACHINED FROM BILLET ALUMINUM - 4.80 LBS. - RECOMMMENDED FOR SPORT STREET OR RACING APPLICAITONS AND GERNERAL REBUILDS. WITH ENGINE UPGRADES AND ALL THE ADDED HORSE POWER THIS TRANSMISSION INTERMEDIATE PLATE IS A MUST. THE FACTORY CAST PLATE IS JUST NOT STRONG ENOUGH TO HANDLE THE ADDED TORQUE. BILLET PIECES ARE MUCH STRONGER AND FITTED TO MUCH CLOSER TOLERANCES PART NUMBER PMP901INT
SIDE SHIFT ROD KIT - PORSCHE 914 – 901 SIDE SHIFT TYPE TRANSAXLE - INCLUDES: NEEDLE BEARING APEX JOINT, BRONZE BUSHING KIT, STAINLESS STEEL REAR BUSHING CUP AND HARDWARE. YOUR FACTORY SHIFT ROD HAS HAD 30+ YEARS OF SAND, SALT, AND WATER THE JOINT AND REAR BUSHING ARE PROBABLY WORN AND CAUSING YOU GRIEF SHIFTING AND POSSABLY DAMAGE TO YOUR TRANSMISSION. THIS IS AN EASY REPLACMENT. ALSO INSTALL THE PMP914FWSB SHIFT ROD BEARING AT THE SAME TIME AND GET A BETTER THAN NEW FEEL.
PART NUMBER PMP914RSR
- PATRICK MOTORSPORTS EXCLUSIVE-
REMOTE OIL FILTER MOUNT - FREE FLOW RIGHT TO LEFT - AN-12 FITTINGS - GAUGE FEED PORT 1/8 NPT - BILLET ALUMINUM FOR USE WITH 13/16 INCH HP-4 FRAM RACING FILTER - PETERSON - LIST: $94.73 PART NUMBER OIL 09-0304
BUSHING SET - REAR CONTROL ARMS - PORSCHE 914 - DELRIN PART NUMBER SUSRDCABUSH