993 RSR EVO II | 3.8L ITB | 6 SPEED
We started with a '96 993 coupe and completely converted it to full race RSR GT II configuration. We used all EVO II lightweight composite glass body work including the roof skin, and flush mount lightweight LEXAN windows. On the scales we are 2,360 lbs.. We spared no expense or detail on this car, Take a good look ! The engine is a 964 based 3.8L "RSR", utilizing all the tricks, "RSR" big valves & seats, Sprint cams, TWM manifold system, Hand made full race 1-7/8" stainless headers w-merge collector & rear cross over secondary merge exit. We are utilizing the very best in MOTEC with the M880 (mill spec.) ECU, ADL2 dash, with 16meg. of data logging. We are now setting the car up with inferred tire temperature sensors & suspension ride height/travel sensors. The engine makes 390+ HP on our DYNOJET XLC224 chassis dyno, and this RSR moves out quickly ! We have built two 993 6 spd transaxles, one has the RSR 8:32= 4.0 to 1 R&P with all short gears "sprint trans". Our second transaxle has the 9:31=3.44 F.D. w- short gears, both with our PMS billet side cover to reduce gear deflection & wear, along with all our tricks, and a super efficient SETRAB oil cooler, this system is "for life" ! We stripped the entire chassis bare, seam welded the tub & hand fabricated the complete roll cage safety system. The cage is FIA approved, the main hoop, "A" pillars & rear downward bars are built in 1.750" DOM .120" wall tubing, the rest in 1.50" DOM .095 wall. The front & rear chassis tubes are also 1.50" DOM .095". The car has on board air jack system"KRONTEC" that really make it nice to set up & service. We have just completed a diet program & went thru the car to replaced the floor pans and seat mount to get the driver as low as possible, it worked ! "See the race photo" We have just converted and reconfigured the dash & switch area, finished in red wrinkle powder coating, among the details. FUELSAFE cell of course, and just look at the photos, no detail spared !
559
Leading the pack.
Patrick Motorsports is an Authorized MoTeC Distributor. We specialize in: Complete Systems Solutions - Engine Management - Data Logging - Full Product Support. Please contact MoTeC Porsche Systems Specialist, Steve Starrick for a system consultation.
This picture shows the FUE SA 117 FUEL CELL which includes the 100 mm double dry brake system. When a fuel cell is wanted or required there is no finer choice than a fuel safe fuel cell. They are used and approved by all sanctioning bodies in every racing application from off road to Indy. If you are looking for a fuel cell, fuel safe should be your first and only choice!
THIS SHOT SHOWS THE PETERSON OIL TANK - 16 QUART (4 GALLON) ALUMINUM (RACE) - DUAL BREATHER - 9 INCHES DIA. X 19 INCHES TALL PART NUMBER OIL 08-0011-DB - ALSO USE BILLET ALUM. BRACKETS OIL08-0101 - LIST: $467.30
YOU CAN ALSO SEE OUT TRANSMISSION COOLER SYSTEM CONNECTED TO THE TOP OF THE TRANSMISSION AND THE COOLER ON THE LEFT UNDER THE BLACK DUCT WORK.
NEXT TO THAT IS THE MOCAL 180 DEGREE OIL THERMOSTAT PART NUMBER OIL-12THER ALL PLUMBED WITH GOODRIDGE FITTINGS AND STAINLESS STEEL HOSES.
THIS SHOT SHOWS THE PETERSON OIL TANK - 16 QUART (4 GALLON) ALUMINUM (RACE) - DUAL BREATHER - 9 INCHES DIA. X 19 INCHES TALL PART NUMBER OIL 08-0011-DB - ALSO USE BILLET ALUM. BRACKETS OIL08-0101 - LIST: $467.30
BELOW THAT IS THE TILTON OIL / WATER PUMP - USED ON TRANSAXLE COOLER SYSTEMS - LIGHTWEIGHT - 3/8" NPT INLET / OUTLET - 12 VOLT - BUNA - INCLUDES BYPASS - 60 PSI WORKING PRESSURE - 1-2 GPM FLOW RATE PART NUMBER ELE TIL 40-524
TOE STEERING LINK - REAR - PORSCHE 993 '95-98'- ADJUSTABLE - 2 PER CAR - HIGH QUALITY SELF LUBRICATED BEARINGS AND BILLET ALUMINUM / STAINLESS STEEL HARDWARE
SUS 993 005
KINEMATICS LINK - REAR - PORSCHE 993 - ADJUSTABLE - 2 PER CAR - HIGH QUALITY SELF LUBRICATED BEARINGS AND BILLET ALUMINUM / STAINLESS STEEL HARDWARE SUS 993 004
THE BRAKE PACKAGE WE CHOSE IS THE BREMBO 4 PISTON CALIPERS WITH SLOTTED ROTORS.
YOU CAN ALSO SEE THE COIL OVER FRONT SUSPENSION WITH EIBACH PREGRESSIVE TENDER AND MAIN SPRINGS AND THE FACTORY OIL COOLER. WE USE GOODRIDGE STAINLESS STEEL BRAIDED HOSES AND FITTINGS WITH ALL OUR OIL COOLER INSTALLATIONS AND UPGRADES.
THIS SHOT SHOWS THE TRANSMISSION REBUILD IN PROGRESS. YOU CAN ALSO SEE THE RETURN FITTING FOR THE TRANSMISSION COOLER SYSTEM WE ARE INSTALLING. WE USE ONLY THE FINEST COMPONENTS IN OUR UPGRADES. INCLUDING THE TILTON OIL PUMP TO CIRCULATE THE TRANS FLUID THROUGH THE SETRAB COIL COOLER. ALL FITTINGS AND HOSE ARE GOODRIDGE.
THIS ALSO SHOWS OUR BILETT SIDE COVER WHICH IS A MUST FOR THE HIGHER HORSE POWER
APPLICATIONS TO ADD NEEDED STRENGTH TO THE DIFFERENCIAL CASE.
A composite roof was added in the second stage of weight reduction. We also completely cut out and re-paneled much of the chassis to reduce as much weight as possible.
