914/6 2.0L Race Car HSR Champion - SOLD 2013

FOR SALE | Porsche 914-6 2.0L Race Car | HSR Champion

914-6 Race Car 2.0L Engine Top Side

914-6 Race Car - Fire Suppression System

914-6 Race Car - Front Oil Tank & Cooler

914-6 Race Car - Front Quarter

914-6 Race Car - Rear Flair

914-6 Race Car - Rear Axle Suspension

This shows the front GT body components starting with the full front hood Porsche 914 this has the backside reinforced and includes metric inserts for hood hinge and striker lightweight composite 16.30 lbs. *Reproduction 914 6 GT part
PART # BOD 914FH

Front bumper cover 914 6 GT includes oil cooler cutout and mounting bracket set lightweight composite *reproduction 914-6 GT PART 
PART # BOD 914GTFBWOC

Lower front valance with spoiler porsche 914 limited edition type with oil cooler cutout and brake ducts for use with non gt flared cars composite
PART # BOD 914LTDWOIL

The front trunk is the heart of our dry sump oil cooling system. 

This starts out with a Peterson OIL TANK (part# OIL 08-0011-DB) - 16 quart (4 gallon) aluminum (race) – dual breather - 9 inch. Diameter X 19 inches tall. Also uses the billet aluminum brackets (part # OIL 08-0101) 

The oil is routed to the engine using Goodridge fittings and stainless braided hoses. From the engine it returns through the Peterson remote oil filter remote mount (part # OIL 09-0304), to the front through the Mocal oil thermostat (part # OIL-12THER), that will route the oil through the front Setrab oil cooler part (# PMP 500-15NPT3/4), when needed to keep the engine at optimum temperature. 

The insulation also includes the Peterson breather/fluid catch tank – spun aluminum type with internal baffling - 2X AN -12 female ports & 1X AN -6AN drain plug – Includes stainless steel strap - 118 MM DIA. - PETERSON FLUID (OIL 08-0400) 

PATRICK MOTORSPORTS is a fully stocked parts dealer - we install what we sell! These parts and all listed on our web site are in stock and ready for shipping worldwide.

REMOTE OIL FILTER MOUNT - FREE FLOW RIGHT TO LEFT - AN-12 FITTINGS - GAUGE FEED PORT 1/8 NPT - BILLET ALUMINUM FOR USE WITH 13/16 INCH HP-4 FRAM RACING FILTER - PETERSON - (PART # OIL 09-0304)


ALSO SHOWS THE ENGINE CARRIER MOUNT - PORSCHE 914 BULK HEAD TO PORSCHE 6 CYLINDER ENGINE CONVERSION - UTILIZES POLYURETHANE BUSHINGS - TIG WELDED STEEL - BLACK POWDER COAT FINISH - 13.50 LBS. 

THESE MOUNTS ARE A MUCH IMPROVED DESIGN OVER THE STOCK FACTORY CROSS BAR AND WITH THE DELRIN BUSHINGS OVER THE FACTORY RUBBER WILL LAST MANY TIMES LONGER. THIS ALSO GIVES YOUR ENGINE CONVERSION A MUCH CLEANER APPEARANCE.

PART #PMP9146FIWAMO

* PLEASE SPECIFY BOLT-IN OR WELD IN TYPE WHEN ORDERING

ON THE RIGHT IS OUR 914 REAR CONTROL ARM CONVERSION PACKAGE (PART #PMP914-RTRAKT)

- SPORT / RACE – FITS ALL PORSCHE 914 CHASSIS - INCLUDES 914 CERTIFIED RECONDITIONED TRAILING ARM SET WITH RECONDITIONED & POLISHED PIVOT SHAFTS, PLATED BEARING RETAINER PLATES, AND BOX REINFORCEMENT KITS. WE ADD D-LOOPS AT THE REAR FOR TOWING & DYNO TIE DOWN POINTS, AND THEN FINISH THEM IN BLACK POWDER COATING. 
DON’T TRUST YOU OLD STOCK FACTORY CONTROL ARM TO HANDLE THE ADDED HORSEPOWER OF YOUR ENGINE CONVERSION. THEY WERE NOT DESIGNED FOR THAT AND WEAKEN WITH AGE. THEY RUST OUT FROM THE INSIDE AS THEY TRAP MOISTURE WHEN THE DRAIN PASSAGES ARE PLUGGED WITH DIRT OR DEBRIS. DON’T FIND OUT THE HARD WAY THAT YOURS WERE WEAK. 
ALSO, NOW IS THE TIME TO ADD THE DELRIN BUSHINGS, (PART# SUSRDCABUSH), NEW WHEEL BEARINGS (PART # DRI 99905303500) AND 5 BOLT HUBS (PART # DRI 91131106533) FOR YOUR WHEEL AND TIRE SWAP. ALSO THE REAR TOE ADJUSTING KIT (PART# PMP914RTOEKIT)

ON THE FIRE WALL YOU CAN SEE THE RIGHT SIDE FOR OUR 914 ENGINE MOUNT FOR 6 CYLINDER CONVERSIONS. THIS MOUNT IS DESIGNED AND MANUFACTURED HERE AT PATRICK MOTORSPORTS. THE MOUNT SHOWN IS OUR WELD-IN MOUNT. THE CENTER SECTION THAT BOLTS TO THE ENGINE CAN PIVOT SO FUTURE REPAIRS CAN BE MADE MUCH EASIER. 

THE FRONT SUSPENSION IS RSR / 935 'SPECIAL UPDATED TYPE' 19 MM RAISED SPINDLE REPOSITIONED - 220/100 VALVING - - 19 MM INCREASED SPINDLE HEIGHT - PORSCHE 911 '72-'89 "A" OR "S" CALIPER / 911 TURBO THRU '89 - 89 MM BOLT HOLE SPACING - BILSTEIN.
PART NUMBERS SUS VE3 61017 - SUS VE3 61018

AT THE TOP IS THE STRUT MOUNT KIT - SOLID TYPE WITH MONO-BALL BEARINGS - PORSCHE 911 THRU '89 & 914 - ADJUSTABLE WITH -1 DEGREE PRE OFFSET - CNC MACHINED 6061 BILLET ALUMINUM - BLACK ANODIZED (SUS 911 343 002 KIT)

BEHIND THE STRUT YOU CAN ALSO SEE THE END OF THE ANTI-SWAY BAR SYSTEM FRONT - PORSCHE 912 / 914 / 911 / 930 '65-'89 - 25 MM HOLLOW LIGHTWEIGHT (STIFFNESS OF SOLID 22 MM BAR) HEAT TREATED 4130 CHROME MOLY - INCLUDES: FULLY ADJUSTABLE 6061-T6 ALUMINUM BEARING BLOCKS, DROP LINKS AND ARMS WITH ZINC PLATED STEEL HARDWARE **1974-89 MODELS ALSO USE: U-BRACKET ADAPTOR - SUSSBRFADP2 & NUT PLATE ADAPTOR PART NUMBER- SUSFSB1950 ** 

The lightweight hollow sway bars are half the weight of a 22mm solid bar with the same stiffness. They are fabricated from aircraft-quality 4130 chrome moly alloy steel and heat treated to maximize strength and reliability.

Bearing blocks, drop links, and swaybar arms are CNC machined from aircraft-quality 6061-T6 aluminum for its high strength to weight ratio.
Fully adjustable front and rear drop links to eliminate suspension preload.

Correctly sized, precision Teflon-lined rod-ends for smooth and quiet operation, long life, and high reliability. No wear and rattling problems, like those seen with other designs, due to undersized or low quality rod ends.
All necessary hardware is provided in zinc plated metric class 8.8
The adjustable drop-link arm connection design provides an infinitely adjustable swaybar stiffness rate and makes it quick and easy to fine-tune your car's handling for various track conditions and driving styles.
Thermoplastic bushings impregnated with Teflon and reinforced with Kevlar provide smooth operation, long life, and high resistance to deflecting under heavy loading.
Optimized geometry for bind free operation throughout the entire suspension range of travel.

All components are designed and manufactured to the highest quality standards, resulting in the finest and most reliable swaybar on the market. 
PART NUMBER SUSFSBA22F